Fisher & Paykel Out-Of-Balance Switch Assembly. Includes Wiring Harness. NOTE! This kit is a complete REPLACEMENT for the older style switch and may appear very different than your original. ALL parts in kit must be replaced. Replacement for items 426597 425626

Lid Lock Assembly for Fisher & Paykel Washers. Includes Wiring Harness. Fits Models GWL11, IWL12 and IWL15. WILL NOT FIT GWL 15 or IWL16 Series!

Display Board for Fisher & Paykel  IWL12 and IWL15 Series. Fits these models/product codes: IWL12 96154 96154B IWL15 96192 96192A

420794P Fisher Paykel Washer Shaft Drive Kit. Driveshaft assembly for Fisher Paykel Washers. Includes agitator nut and rotor cap.

420807 Fisher & Paykel Control Panel overlay for Model GWL11 and GWL15 US washers. Replaces AP6790892, 420068. Part is a peel-and-stick part. Not returnable. May differ slightly in appearance from original. Genuine Fisher Paykel Factory Replacement Part.

Water inlet nozzle and elbow for Fisher & Paykel EcoSmart Washers. Replaces old Nozzle part # 420143 and Elbow # 425974P. The nozzle may appear different than your original nozzle. This is the most current nozzle from the factory and previous design is obsolete. NOTE! If you need this part you may be overloading your washer! This part can be damaged by having too many items in the washer.

420952P Tub Support Rods for Fisher & Paykel Smartdrive and Intuitive ECO washers GWL03 GWL08 GWL10 GWL11 GWL15 IWL12 IWL16 WA37T26. Includes all 4 rods. Spring and shock for tub support. Replaces obsolete part # 426750P. If you would like to purchase just a single rod assembly, we offer them under part #420952P-S NOTE: WILL NOT FIT "AQUASMART" SERIES. Use part # 421127P for the Aquasmart washers.

420952P-S Tub Support Rod for Fisher & Paykel Smartdrive and Intuitive ECO washers GWL03 GWL08 GWL10 GWL11 GWL15 IWL12 IWL16 WA37T26. This is a SINGLE rod. Spring and shock for tub support. Replaces obsolete part # 426750P. If you would like to purchase a complete set of 4, we offer them under part #420952P NOTE: WILL NOT FIT "AQUASMART" SERIES. Use part # 421127P for the Aquasmart washers.

Water inlet valve assembly for Fisher & Paykel AQUASMART series washers. DOES NOT FIT ECOSMART! Fits these models and product codes: WL26CW1 93615-A 96215-B WL26CW2 96137-A WL37CW2 96114-A 96114-B WL37T26DW1 96215-A 96215-B NOTE THIS IS A 4-COIL VALVE. DOES NOT FIT 5-COIL models.

Support Straps for Fisher Paykel Aquasmart washers. Set of 4. Fits on each corner of machine from tub support rods to tub collar. Always replace as a set. For all "Aquasmart" washers.

421039P Fisher Paykel Aquasmart Washer Agitator. Includes cap and fastener. Replaces 421039. Fits Aquasmart models WL26CW WL37T26CW WL42T26CW2 WL42T26CW1. DOES NOT FIT ECOSMART MODELS!

421098P Fisher Paykel Washer Display Board. Fits GWL11, GWL15, WA37T26, WA42T26. Does not include overlay. Includes wiring harness.

Fisher & Paykel 421177P Water Inlet Valve for GWL15US WA37T26 IWL16, WA42T26GW1. Replaces old part numbers 420753P and 421029P. Genuine Fisher & Paykel Factory Replacement Part.

421226USP Fisher Paykel Aquasmart Washer Control. Replaces 420579USP. Click MORE DETAILS for specific model compatibility information.

421306USP Fisher Paykel Washer Motor Control Board. Fits GWL15 IWL15 IWL16 WA37T26 Series US washers. Factory Replacement for obsolete part # 420811USP 420811 478089USP and 478145USP.

IMPORTANT NOTE- PLEASE READ CAREFULLY! All machine controls are factory reconditioned. This is the only option available for this part. This is as dictated by the factory. Electronic parts are NOT RETURNABLE!

NOTE: Before you order or replace the controller on your Fisher-Paykel washer, please read this article over carefully! Machine controls are often replaced, only to fail again shortly after replacement. The reason for this is because there was an underlying condition that caused the control to fail in the first place, such as a wet or shorted water pump. Before you replace your machine control, tip the machine back and check the condition of the WATER PUMP. Look for signs of rust, leakage or seepage thru the seal, and also look for a burnt or discolored coil on the pump's motor. The pump may even smell "burnt" to you. If you install a new control in a machine with a shorted or leaky water pump, your new control will fail again, perhaps as soon as the first load of wash. If your pump is bad, it MUST be replaced along with the machine control.