Support Straps for Fisher Paykel Aquasmart washers. Set of 4. Fits on each corner of machine from tub support rods to tub collar. Always replace as a set. For all "Aquasmart" washers.

421039P Fisher Paykel Aquasmart Washer Agitator. Includes cap and fastener. Replaces 421039. Fits Aquasmart models WL26CW WL37T26CW WL42T26CW2 WL42T26CW1. DOES NOT FIT ECOSMART MODELS!

421098P Fisher Paykel Washer Display Board. Fits GWL11, GWL15, WA37T26, WA42T26. Does not include overlay. Includes wiring harness.

Fisher & Paykel 421177P Water Inlet Valve for GWL15US WA37T26 IWL16, WA42T26GW1. Replaces old part numbers 420753P and 421029P. Genuine Fisher & Paykel Factory Replacement Part.

421226USP Fisher Paykel Aquasmart Washer Control. Replaces 420579USP. Click MORE DETAILS for specific model compatibility information.

421306USP Fisher Paykel Washer Motor Control Board. Fits GWL15 IWL15 IWL16 WA37T26 Series US washers. Factory Replacement for obsolete part # 420811USP 420811 478089USP and 478145USP.

IMPORTANT NOTE- PLEASE READ CAREFULLY! All machine controls are factory reconditioned. This is the only option available for this part. This is as dictated by the factory. Electronic parts are NOT RETURNABLE!

NOTE: Before you order or replace the controller on your Fisher-Paykel washer, please read this article over carefully! Machine controls are often replaced, only to fail again shortly after replacement. The reason for this is because there was an underlying condition that caused the control to fail in the first place, such as a wet or shorted water pump. Before you replace your machine control, tip the machine back and check the condition of the WATER PUMP. Look for signs of rust, leakage or seepage thru the seal, and also look for a burnt or discolored coil on the pump's motor. The pump may even smell "burnt" to you. If you install a new control in a machine with a shorted or leaky water pump, your new control will fail again, perhaps as soon as the first load of wash. If your pump is bad, it MUST be replaced along with the machine control.

421613P Fisher Paykel WL42 Aquasmart Washer Modular Display. Fits WL42 series Aquasmart washers. Genuine Fisher Paykel factory replacement part.

424314P Lid Lock Assembly for Fisher & Paykel GWL15, IWL16, WL26CW WL37T26 WA37T26 WA42T26 WL42T26 Series. Direct replacement for 420700, 420700P. NOTE: WILL NOT FIT GWL11, IWL12 or IWL15 Series!

424348P Fisher Paykel Washer RPS Sensor Kit. Replaces obsolete 420776P. Includes instructions and updated wiring harness assembly. Typically required when fault code 130 or 131 is generated. RPS Sensor for following model series: GWL15US WL37CW WL37T26DW WA37T26DW IWL16 WL26CW NOTE! This part will NOT fit GWL11 and earlier series.

Fisher & Paykel Washer Thermistor and Seal assembly , includes grommet and wiring harness.

424495P Fisher Paykel AquaSmart Washer Support Rods. Set of 4. Genuine Fisher & Paykel part. Replaces 421127P, 421067P. Fits AQUASMART models only! Will NOT fit the Ecosmart series! Fits: WL26CW1 WL37T26KW WL26CW2 WL42T26DW1.

425025P Agitator for Fisher & Paykel Washers. Replaces 478083P, AP6791048. Fits GWL03 GWL08 GWL10 GWL11 GWL15 IWL12 IWL16 WA37T26 WA42T26C Models. Does not include Fabric Softener Dispenser. Easy to change, requires no tools and takes all of 2 minutes to complete the job. Don't pay an expensive service call, order today and do it yourself!

Fisher & Paykel Washer water inlet elbow for Ecosmart washers. Genuine Fisher & Paykel Factory Replacement Part.

426055PC Console for GWL10 models. Includes 426055P Console frame and 426872P Overlay. DOES NOT INCLUDE CONTROL BOARD. This is the plastic console and overlay only. You must transfer the LED Board from your existing unit to the replacement. This part is typically replaced when buttons crack or break. See part # 426997USP for LCD control.

426142P Fisher Paykel Hot Water Inlet Valve. Fits GWL08US Models.